new products sale 202208
Home > DIY Module > Funny DIY > DIY Kit Analog Electronic Candle Lights Happy Birthday Thermal Sensor MIC Sound Control Simulation Candle DIY Learning

DIY Kit Analog Electronic Candle Lights Happy Birthday Thermal Sensor MIC Sound Control Simulation Candle DIY Learning

5 9
$5.49 (only 0 pcs )
Contact us for wholesale price

Sold out

Tested by ICStation Outstanding Partner:
    This circuit simulates a real candle, lit with fire, and blown out with a mouth. Light up and play the "Happy Birthday to You" song, stop playing the music when it blows out.
    1>.Simulating candle
    2>.More realistically imitating candles
    3>.DIY custom installation
    4>.Learning circuit
    5>.Practice welding
    1>.Product Name:DIY Kit Analog Electronic Candle Light
    2>.Work Voltage:DC 5V
    3>.Work Temperature:-40℃~85℃
    4>.Work Humidity:0%~95%RH
4.Circuit Principle:
This circuit uses a D flip-flop to form an R-S flip-flop.
After the power is turned on, the differential circuit composed of R7 and C4 generates a high-level differential pulse, then outputs it to the RST terminal of IC1, forcing the circuit to reset. The Q terminal outputs a low level, and outputs to the base of the triode VT5 and VT6. VT5. VT6 is cut off, the LED is not lit, and the buzzer does not ring.
When the thermistor Rt is burned with a lighter (the burning time is too long and the thermistor is easily burned out), the resistance of R1 suddenly becomes small, showing a low resistance state.
The triode VT1/VT2 is turned on successively (Rp1/Rp2 can be separately adjusted for VT1/VT2 on-time), the high-level pulse generated is output to the SET terminal of IC1, the Q-end is turned to a high level, and the output is applied to the base of the transistor VT5/VT6, and the triode VT5/VT6 is turned on.
LED turn ON, the buzzer plays the "Happy Birthday to You" piece. This process is equivalent to lighting the candle with a match. At this time, even if the lighter leaves the thermistor Rt, the state of the circuit does not change.
When the wind blows toward the microphone M1, the audio signal output by the microphone M1 is output to the base of the VT3 through C3, and the VT3 is turned on.
Because the resistance of R5 is relatively large, the collector potential of VT3 drops very low, the base potential of PNP transistor VT4 is very low, VT4 is turned on, and the high level pulse is output to the RST terminal of the flip-flop.
The trigger is reset, the Q terminal changes from high level to low level, VT5/VT6 is cut off, the light emitting diode is off, and the buzzer stops playing the "Happy Birthday to You" music, realizing the simulation effect of "wind blowing out".
5.Using Steps:
    1>.Complete the correct installation according to ‘Installation Steps’.
    2>.Connect 5V power supply.
    3>.Use a lighter to burn the thermal sensor about 2second(Can not for more time.Otherwise it will damage the sensor)
    4>.LED will turn ON and Buzzer playing ‘happy birthday to you’.The buzzer can only simulate playback, the quality of the voice is not very good, please note.
    5>.Blowing towards the microphone, the LED will go out and the buzzer will stop playing.
    1>.User needs to prepare the welding tool first.
    2>.Please be patient until the installation is complete.
    3>.The package is DIY kit, not finished products.
    4>.The soldering iron can't touch the components for a long time(1.0 second), otherwise it will damage the components.
    5>.Pay attention to the positive and negative of the components.
    6>.Strictly prohibit short circuit.
    7>.Users can complete installation by PCB silk screen and component lists.
    8>.The buzzer can only simulate playback, the quality of the voice is not very good, please note.
    9>.It is strongly recommended to read the installation manual before starting installation.
7.Installation Steps
    1.Install SMD components at first.
    2.Install complex components preferentially.
    3.Pay attention to the installation direction of components.
    4.Make sure the soldering iron does not touch the components for a long time.Otherwise it is easy to damage the components.
    Step 1:Install 4pcs 560ohm 0805 SMD resistor at R11-R14.
    Step 2:Install 8pcs 1Kohm 0805 SMD resistor at R15-R22.
    Step 3:Install 2pcs 1Kohm 0805 SMD resistor at R8-R9.3pcs 10Kohm at R2,R4,R6. 2pcs 100ohm at R10,R23.
    Step 4:Install 1pcs 360ohm 0805 SMD resist or at R3.1pcs 20Kohm at R1. 1pcs 1Mohm at R5.1pcs 100Kohm at R7.
    Step 5:Install 1pcs SOP-14 CD4013 at IC2.Pay attention to the installation direction, adjacent pins can not be shorted.
    Step 6:Install 1pcs 1N4007 at VD1 and 1pcs 1N4148 at VD2.
    Step 7:Install 1pcs 10Kohm Thermistor at Rt.But pay attention to the installation method, the sensor can not be close to the PCB, and it needs to stretch about 5mm.
    Step 8:Install 2pcs 103 ceramic capacitor at C1,C2.2pcs 104 ceramic capacitor at C3,C4.1pcs 102 ceramic capacitor at C5.
    Step 9:Install 3pcs S9012 at VT1,VT2,VT4.3pcs S9013 at VT3,VT5,VT6.1pcs S8050 at VT7.
    Step 10:Install Bending Male Pin at +5V and GND.
    Step 11:Install 8pcs 3mm Red LED at LED6-LED13.
    Step 12:Install 4pcs Red LED at LED2-LED5 and 1pcs RGB LED at LED1.
    Step 13:Install 1pcs Microphone at M1.Pay attention to the installation direction.
    Step 14:Install 2pcs potentiometer at Rp1,Rp2.1pcs Passive Buzzer at LS1.
    Step 15:Install 1pcs LX9300 Voice Chip at IC2.
Note:It just need to install Pin-1/Pin-3/Pin-5. Other pins do not need to be installed.





There are currently no product reviews.

First we should say that ICStation doesn't accept any form of pay on delivery.Items used to be shipped after receiving the order info and payment.

1) Paypal Payment

PayPal is a secure and trusted payment processing service that allows you to shop online. PayPal can be used at to purchase items by Credit Card (Visa, MasterCard, Discover, and American Express), Debit Card , or E-check (i.e. using your regular Bank Account). 

We are PayPal Verified 


2) West Union


We know that some of you do not have the Paypal account. 

But please take it easy. You can use West Union payment method.
Learn more at West Union at
For the receiver info, please contact us at
3) Bank Transfer / Wire Transfer / T/T

Bank Transfer / Wire Transfer / T/T payment methods are accepted for orders which the total price is up to US$500. The bank will charge about US$60 for the transfer fee if we do the payment in these ways. 

For other payment method, please contact us at for more details.

1. Yanwen / YunExpress / 4PX / China Post Airmail Service

(1) Due to the high risk of package lost recently, we have to stop using the free shipping way these days. Hope for your kind understanding! And the $5 is for tracking number and delivery insurance ^0^ Enjoy order from us. 

Free Shipping for all orders over $20 ^0^ (with free tracking number and delivery insurance fee)

(2) Shipping time 
Shipping time is 7-20 business days to most of countries; please view below table for exactly shipping time to your location. 

7-15 working days to: Most of Asia countries
10-16 working days to: USA , Canada , Australia , UK , Most of Europe countries
13-20 working days to: Germany , Russia
18-25 working days to: France , Italy , Spain , South Africa
20-45 working days to: Brazil , Most of South America countries

2. DHL/FedEx Express

(1)Shipping Fee: Free for the order which meet the following requirements
Total price of the order >= 200USD or Total weight of the order >= 2.2KG

When the order meets to one of the above requirement, it will be shipped for FREE via EMS/DHL/UPS Express to below country. 
Asia: Japan , South Korea , Mongolia . Malaysia , Singapore , Thailand , Vietnam , Cambodia , Indonesia , Philippines 
Oceania: Australia , New Zealand , Papua New Guinea 
Europe& America: Belgium, Britain, Denmark, Finland, Greece, Ireland, Italy, Luxembourg, Malta, Norway, Portugal, Switzerland, Germany, Sweden, France, Spain, USA, Austria, Canada
Note: Shipping Fee to other countries, please contact

(2) Shipping Time & Delivery Time

Shipping time: 1-3 days
Delivery time: 5-10 working days (about 1-2 weeks) to most of countries. 

Because the package would be returned to the sender if it had not been signed by the receiver , please pay attention to the arriving time of the package. 


1) APO and PO Box Addresses

We strongly recommend that you provide a physical address for order delivery. 
Because that DHL and FedEx are unable to deliver items to APO or PO BOX addresses. 
2) Contact Phone Number
Receivers' contact phone number is required by express shipping agency for the package delivery. Please provide us with your latest phone number.

3. Note
1) Delivery Time of mixed orders with items in different Shipping Status should be calculated using the longest estimate times listed. 
2) Chinese Holiday Reminder: During annual Chinese holidays, services from certain suppliers and carriers may be affected, and delivery for orders placed around the following times may be delayed by 3 - 7 days: Chinese New Year; Chinese National Day,etc. 
3) Once your order is shipped, you will receive an email notification from
4) Track the order which with tracking number via below links:

YunExpress / Yanwen / China Post:


Customers who bought this product also purchased

Your Recent History