holiday notice 2024
Home > Function Module > Voice Module > Mini MP3 Player Module Audio Voice Board 8Bit I/O UART Control Support SD Card TF Card

Mini MP3 Player Module Audio Voice Board 8Bit I/O UART Control Support SD Card TF Card

13288
5 9
$2.49 $1.74
Quantity10+30+50+
Price$1.60$1.40$1.20
Contact us for wholesale price
Time Remaining:
- OR - - OR - Add to Wish List

Description:
XY-V17B is an intelligent voice module developed by the division independently. It integrates IO subsection triggering, UART serial port control, ONE_line single bus serial port control, and standard MP3, etc. Support MP3,WAV decoding format. Max support 32G TF card storage, can connect the computer to update TF card to store audio files via USB cable.

Features:
1>. Support MP3 and WAV decoding format.
2>. Support sampling frequency (KHz) : 8/11.025/12/16/22 05/24/32/44.1/48.
3>. 24-bit DAC output, dynamic range support 90dB, SNR support 85dB.
4>. Fully support the FAT16/FAT32 file system, with the maximum support 32GB TF card and 32GB U-disk.
5>. Support UART serial port control voice broadcast function, can control playback, pause, selections, turn up and down volume and other functions, the largest selection of 65535 tracks.The baud rate is 9600 bit/s.
6>. Support IO trigger function, 8 IO ports can trigger 8 musics or 8 IO combinations to trigger 255 songs.
7>. Support One_line single bus serial port control, which can control playback, pause, selection, turn up and down volume and other functions.
8>. Support 3 configuration IO for mode selection.

Download the Operation Manual here:



 

 

Tested by ICStation's Outstanding Partner adrirobot:

https://www.adrirobot.it/XY-V17_B-D/modulo_XY-V17-B-D.htm



Module Pin Instructions:


 

No. Pin Name Instruction
1 IO0/UART_TX IO trigger mode is input IO0;UART mode is TX.
2 IO1/UART_RX IO trigger mode is input IO1;UART mode is TX pin.
3 IO2 IO trigger mode input IO2.
4 IO3 IO trigger mode input IO3.
5 IO4/ONE_LINE IO mode input IO4;One_Line mode data sends pins.
6 IO5 IO trigger mode input IO5.
7 IO6 IO trigger mode input IO6.
8 IO7 IO trigger mode input IO7.
9 GND Ground
10 CON1 Mode Configuration pins 1.
11 CON2 Mode Configuration pins 2.
12 CON3/BUSY Mode Configuration pins 3; Busy output, Playing output High,Pause output LOW.
13 USB_DM USB DM signal
14 USB_DP USB DP signal
15 VDD/5V Module power supply, 3.3-5V voltage input .
16 3.3V LDO 3.3V output , maximum output current 100mA.
17 DACL Audio left channel output.
18 DACR Audio right channel output.


Module Dimensions:



Mode Configuration and Pin Function:

Control Mode Configuration Pin I/O Function
CON3 CON2 CON1 IO7 IO6 IO5 IO4 IO3 IO2 IO1 IO0
I/O Integrated Mode 0 0 0 0 Key combination play, can play 2^8-1(255) Songs.
I/O Integrated Mode 1 0 0 1 Level combination play, can play 2^8-1(255) Songs.
I/O Independent Mode 0 0 1 0 Music 8 Music 7 Music 6 Music 5 Music 4 Music 3 Music 2 Music 1
I/O Independent Mode 1 0 1 1 Music 8 Music 7 Music 6 Music 5 Music 4 Music 3 Music 2 Music 1
UART Mode 1 0 0             RXD TXD
One-Line Mode 1 0 0       TXD        
Standard MP3 Mode 1 0 1       RPT EQ P/P/MODE PREV/V- NEXT/V+


Note:
1>. "key combination play" : Return to the original high level after the corresponding level from I/O0-I/O7 output, similar to the key triggered once.Similar instantaneous switch.
2>. "Level combination play" :The trigger signal remains the same, similar to a self-locking switch.
3>.The difference between “I/O Integrated/Independent Mode 0” and “I/O Integrated/Independent Mode 1” :Mode 0 will continue playing the current song to the end after release level .Mode 1 will stop playing immediately after release level.


Mode Operation Instruction:
1>. I/O integrated mode 0(Key combination playing).
It will stop playing current song to the end after I/O0-7 release input signal(return to high) at 'I/O Integrated Mode';It will playing new song when get new input signal during playing and stop after end of song;It will play repeatedly if keep input;Busy pin will output valid signal(High) during playing.
Note: the song must be named for 5bit.
Music control:

IO7 IO6 IO5 IO4 IO3 IO2 IO1 IO0 Song
1 1 1 1 1 1 1 0 00001.mp3
1 1 1 1 1 1 0 1 00002.mp3
1 1 1 1 1 1 0 0 00003.mp3
1 1 1 1 1 0 1 1 00004.mp3
1 1 1 1 1 0 1 0 00005.mp3
1 1 1 1 1 0 0 1 00006.mp3
1 1 1 1 1 0 0 0 00007.mp3
...... …… …… …… …… …… …… …… ……
0 0 0 0 0 0 0 0 00255.mp3

2>. I/O integrated mode 1(Level combination playing)
It will keep playing current song when get trigger signal.It will stop playing immediately after release level. Busy pin will output valid signal(High) during playing.Note: the song must be named for 5bit.
Music control:

IO7 IO6 IO5 IO4 IO3 IO2 IO1 IO0 Song
1 1 1 1 1 1 1 0 00001.mp3
1 1 1 1 1 1 0 1 00002.mp3
1 1 1 1 1 1 0 0 00003.mp3
1 1 1 1 1 0 1 1 00004.mp3
1 1 1 1 1 0 1 0 00005.mp3
1 1 1 1 1 0 0 1 00006.mp3
1 1 1 1 1 0 0 0 00007.mp3
…… …… …… …… …… …… …… …… ……
0 0 0 0 0 0 0 0 00255.mp3

3>. I/O independent mode 0((Key independent controlling)
I/O0-I/O7 independently controls 8 songs.It will stop playing current song to the end after I/O0-7 release input signal(return to high);It will playing new song when get new input signal during playing and stop after end of song;It will play repeatedly if keep input;Busy pin will output valid signal(High) during playing.
Note: the song must be named for 5bit.

IO7 IO6 IO5 IO4 IO3 IO2 IO1 IO0 Song
1 1 1 1 1 1 1 0 00001.mp3
1 1 1 1 1 1 0 1 00002.mp3
1 1 1 1 1 0 1 1 00003.mp3
1 1 1 1 0 1 1 1 00004.mp3
1 1 1 0 1 1 1 1 00005.mp3
1 1 0 1 1 1 1 1 00006.mp3
1 0 1 1 1 1 1 1 00007.mp3
0 1 1 1 1 1 1 1 00008.mp3

4>. I/O independent mode 1(Level independent controlling)
I/O0-I/O7 independently controls 8 songs.It will keep play repeatedly specify the triggered song.It will stop playing immediately after release level.Busy pin will output valid signal(High) during playing.
Note: the song must be named for 5bit.

IO7 IO6 IO5 IO4 IO3 IO2 IO1 IO0 Song
1 1 1 1 1 1 1 0 00001.mp3
1 1 1 1 1 1 0 1 00002.mp3
1 1 1 1 1 0 1 1 00003.mp3
1 1 1 1 0 1 1 1 00004.mp3
1 1 1 0 1 1 1 1 00005.mp3
1 1 0 1 1 1 1 1 00006.mp3
1 0 1 1 1 1 1 1 00007.mp3
0 1 1 1 1 1 1 1 00008.mp3

5>. UART serial port mode
     5.1>. Communication format
Adopt full duplex serial port communication;
Baud rate 9600, data bits 8, stop bit 1, check bit N.
Start code - command type - data length (n) - data 1- data n- and test (SM)
Command code: fixed to 0xAA.
Command type: used to distinguish the type of command.
Data length: the number of bytes of data in an command.
Data: the relevant data in the command, when the length of data is 1, means that there is only CMD and no data bits.
Test: it is low 8 bits of the sum of all the bytes. that is, When the starting code and the data are added, take out low 8 bits.
Data format: sent data or command, high 8-bit data is in front, low 8-bit is in the back.


     5.2>. Communication protocol
The following is a data definition for the return and identification of the chip.
A. Playing State definition: the system is on the stop state when power on.
00(stop)    01(play)        02(pause)

B. Disk character definition: it is stopped after the switch disk.
USB:00     SD:01     FLASH:02     NO_DEVICE: FF.

C. Volume: the volume is 31grades, 0-30.The default is 20grade.

D. Play mode: the default is the single stop when power on.

Cycle for all songs (00) : play the whole songs in sequence and play it after the play.
Single cycle (01) : play the current song all the time.
Single stop (02) : Only play current song once and then stop.
Random play (03) : random play.
Directory loop (04) : play the songs in the current folder in order, and then play them after the play. The directory does not contain subdirectory.
Directory random (05): random play in the current folder, and the directory does not contain subdirectory.
Directory order play (06) : play the songs in the current folder in order and stop after the play. The directory does not contain subdirectory.
Sequential play (07) : play the whole songs in order and stop after it is played.

E. EQ definition: the default EQ is NORMAL(00).
NORMAL(00) POP(01) ROCK(02) JAZZ(03) CLASSIC(04)

F. Composition play definition: combination play is combined by filename. The file requirements are stored under the "XY" file. You can change the name of the file you want to combine to two bytes, which is generally recommended as a number. Such as: 01. Mp3, 02. Mp3.


      5.3>. Communication command
Control command:

Command Command Code Return
Play AA 02 00 AC None
Pause AA 03 00 AD None
Stop AA 04 00 AE None
Previous AA 05 00 AF None
Next AA 06 00 B0 None
Volume + AA 14 00 BE None
Volume - AA 15 00 BF None
Previous file AA 0E 00 B8 None
Next file AA 0F 00 B9 None
Stop playing AA 10 00 BA None

Setting Command:

Command Command code Return Remark
Set Volume AA 13 01 VOL SM None VOL:0x00-0xFF
Set Loop mode AA 18 01 Loop-mode SM None Loop-mode:0x00-0x07
Set Cycle times AA 19 02 H L SM None H:0x00-0xFF
L:0x00-0xFF
Set EQ AA 1A 01 EQ SM None EQ:0x00-0x04
Specified Song AA 07 02 S.N.H S.N.LSM None S.N.H:0x00-0xFF
S.N.L:0x00-0xFF
Specified Path AA 08 Length Drive Path SM None Length:0x00-0xFF
Drive:0x00-0xFF
Path:0x00-0xFF
Switch Specified Drive AA 0B 01 Drive SM None Drive:0x00-0xFF
Specified song to be interplay AA 16 03 Drive S.N.H S.N.L SM None Drive:0x00-0xFF
S.N.H:0x00-0xFF
S.N.L:0x00-0xFF
Specified path to be interplay AA 17 Length Drive Path SM None Length:0x00-0xFF
Drive:0x00-0xFF
Path:0x00-0xFF
Select but no play AA 1F 02 S.N.H S.N.L SM None S.N.H:0x00-0xFF
S.N.L:0x00-0xFF

Query Command:

Command Command code Return
Query play status AA 01 00 AB AA 01 01, play status, SM
Query current online drive AA 09 00 B3 AA 09 01, drive, SM
Query current play drive AA 0A 00 B4 AA 0A 01, drive, SM
Query Number of songs AA 0C 00 B6 AA 0C 02S.N.H S.N.L SM
Query current song AA 0D 00 B7 AA 0D 02 S.N.H S.N.L SM
Query folder directory song AA 11 00 BB AA 11 02 S.N.H S.N.L SM
Query folder Number of songs AA 12 00 BC AA 12 02 S.N.H S.N.L SM


6>. One_line Single bus serial port mode

Waveform:


Command format:

Command(HEX) Function Note
00 No. 0 The number 0-9 has corresponding functions, such as selecting music, setting the volume, setting EQ, setting cycle mode, setting channel, setting the repertoire, and sending the digital at first and then send function command.








 
01 No. 1
02 No. 2
03 No. 3
04 No. 4
05 No. 5
06 No. 6
07 No. 7
08 No. 8
09 No. 9
0A Number reset Sent the number of Cleared
0B Confirm choosing song Cooperate with Numbers to achieve.




 
0C Volume setting
0D EQ setting
0E Loop mode setting
0F Channel setting
10 Interplay song setting
11 Play  
12 Pause  
13 Stop  
14 Previous  
15 Previous directory  
16 Next directory  
17 SD card selection  
18 SD card selection  
19 U disk selection  
1A FLASH selection  
1B System sleep  
1C Stop Playing   

Note: "selection" and "interplay" are played according to the track name, for example, the track is named "00123. Mp3", and the selected data is "0x01", "0x02" "0x03" "0x0B", and the selection is completed.

Typical Application Circuit:




 




 



 

Quantity10+30+50+
Price$1.60$1.40$1.20
There are currently no product reviews.

ICStation doesn't accept any form of pay on delivery. Items used to be shipped after payment. Below are the payment methods we can accept at the moment:

1) Paypal Payment

PayPal is a secure and trusted payment processing service that allows you to shop online. PayPal can be used at icstation.com to purchase items by Credit Card (Visa, MasterCard, Discover, and American Express), Debit Card , or E-check (i.e. using your regular Bank Account). 



We are PayPal Verified 

 

2)  Bank Transfer / Wire Transfer / T/T

 

Bank Transfer / Wire Transfer / T/T payment methods are accepted for orders which the total price is up to US$300. The bank will charge about US$50 for the transfer fee if we do the payment in these ways. Feel free to contact us for bank payment details if you need pay via bank.

For other payment method, please contact us at orders@icstation-team.com for more details.

Customers who bought this product also purchased

DIY High Voltage Electromagnetic Transmitter Kit 3V Primary Coil Boost Module STEM Kit for School Home Education
$11.19
$15.99
31
DC 5V 5W Mono Voice Playback Module, 9-Channel Music Power Digital Amplifier 32Mbit Flash MP3 WAV UART Controller for Arduino
$4.19
$5.99
31
DIY Electronic Music Drum Soldering Practice Kit, Touch Sensing SMD Soldering Project Kit with 7 String Lyre Harp, Ideal STEM Project for College High School Education, Competitions and Gifts
$11.19
$15.99
31
USB Voltage Current Meter DC 4V-30V 5.1A USB Charger Multi-Function Detector Voltmeter Ammeter
$8.11
$11.59
31
Voice Playback Module, Music Player Voice prompts Voice Broadcast Device, MP3 Trigger Amplifier Class D 5W 64MBit Flash for Arduino
$4.89
$6.99
31
DC8V-24V Bluetooth Amplifier Board 15Wx2 Stereo Audio Amp with Music Spectrum Display APP Remote Control for DIY Speakers
$9.79
$13.99
31
8M Recordable Voice Play Module, Button Control Sound Module With Volume Adjustment and USB Data Cable For DIY Music Gift Box Greeting Card
$6.99
$9.99
30
ESP32 Type-C USB WiFi Bluetooth-Compatible ESP-WROOM-32 Development Board
$6.29
$8.99
30
5V 64Bit RGB LED Light Board WS2812B 8*8 Dot Matrix Display Screen
$5.59
$7.99
31
FM Wireless Microphone Kits FM Radio Transmitter Module FM 85-115MHz DIY Kits Frequency Modulation Audio MP3 Recorder Radio Experiment Training Kit
$4.19
$5.99
31
DIY Kits Electronic Lucky Rotary Module Wheel Turntable Analog Lottery Tumbler Kit Red Flash LED 3-5V Fun Electronics
$1.00
$1.99
50

Your Recent History

Mini MP3 Player Module Audio Voice Board 8Bit I/O UART Control Support SD Card TF Card
$1.74
$2.49
31