icstation holiday notice 202310
Home > DIY Module > Funny DIY > Photosensitive Mobile Robot Simulation Firefly Electronic DIY Kit

Photosensitive Mobile Robot Simulation Firefly Electronic DIY Kit

GY19603
5 9
$7.99 $5.59
Quantity50+100+200+
Price$4.99$4.75$3.50
Contact us for wholesale price
Time Remaining:
- OR - - OR - Add to Wish List
 
1.Introduction:
SFT-Q03YH is a Photosensitive Mobile Robot Simulation Firefly Electronic DIY Kit.
It can simulate the automatic flashing of fireflies, and automatically move towards light at night according to the photosensitive sensor. 
 
After turning on the switch, the LED light on the tail flashes like a firefly glowing. When the light enters the two antennae, the firefly will move.  A very interesting Mini DIY electronic product, which enables users to understand the circuit more clearly and learn welding skills.
 
Exercise Hands-on Ability: We offer PDF Installation manual to guide you complete it step by step. This was super fun and challenging kit for kids, students, electronics lovers to practice their hands-on ability and soldering skills. Suitable for children and electronic beginners.
 
LED light flashing frequency is adjustable: The flashing frequency of the blue LED light at the tail of the firefly can be adjusted by a potentiometer.  
 
Please kindly noted: The battery is not included. Please prepare a CR2032 Battery by yourself.
 
2.Feature:
1.Photosensitive automatic movement
2.Breathing light flashes automatically
3.Simple circuit
4.High simulation firefly
 
3.Parameter:
1.Product Name:Photosensitive Mobile Robot Electronic DIY Kit
2.Product Number:SFT-Q03YH
3.Work Voltage:DC 3V
4.Work Current:30mA
5.Work Temperature:-40℃~85℃
6.Work Humidity:5%~85%RH
7.Size(Installed):60*60*35mm
 
4.Function:
1.Sensitive movement: There are two photosensitive sensors on right and left (R1/R4) which simulating the antennae of fireflies. When the light reaches the antennae R1 or R4, Transistor Q1 or Q2 will turn ON and then the corresponding motor starts to vibrate, so that the firefly moves in the direction of light.
 
2.Breathing light: The breathing lamp circuit is controlled by lm358 chip, which can simulate the effect of firefly's slow ON and OFF.
 
3.The LED breathing light will turn OFF when moving.
 
5.Component List:
 
6.Schematic:
 
7.Installation Steps (PDF version is available):
Step 1: Install 2pcs 100ohm Metal Film Resistor at R5,R11. Identify the resistor value as shown in color:Brown/Black/Black/Black/Brown.
Step 2: Install 2pcs 430ohm Metal Film Resistor at R2,R3. Identify the resistor value as shown in color:Yellow/Orange/Black/Black/Brown.
Step 3: Install 1pcs 1.5Kohm Metal Film Resistor at R7. Identify the resistor value as shown in color:Brown/Green/Black/Brown/Brown.
Step 4: Install 1pcs 3.3Kohm Metal Film Resistor at R6. Identify the resistor value as shown in color:Orange/Orange/Black/Brown/Brown.
Step 5: Install 2pcs 10Kohm Metal Film Resistor at R9,R10. Identify the resistor value as shown in color:Brown/Black/Black/Red/Brown.
 
Step 6: Install 3pcs XH2.54-2P Male Pin at M1,M2,DC3V.(Users don't have to install them)
Step 7: Install 1pcs DIP-8 IC Socket at U1.There is a groove on one end of the IC Socket and there is a groove mark on PCB where the IC Socket can place on.These two marks are corresponding to each other and are used to specify the installation direction of the IC Socket.
Step 8: Install 2pcs TO-92 S8550 Transistor at Q1,Q2.
Step 9: Install 1pcs TO-92 S9014 Transistor at Q3.
Step 10: Install 1pcs 5mm Blue LED at LED.The longer pin is inserted into mark ‘ + ’ (positive pole).
 
Step 11: Install 1pcs 100uF Electrolytic Capacitor at C1.Pay attention to distinguish between positive and negative.The Longer pin is positive pole which marked ‘ + ’.
Step 12: Install 1pcs Power Switch at K.
Step 13: Install 1pcs 10Kohm Potentiometer at R8.
Step 14: Install 1pcs DIP-8 IC LM358P at U1.There is a groove on one end of the IC and there is a groove mark on PCB where the IC can place on.These two marks are corresponding to each other and are used to specify the installation direction of the IC.
Step 15: Install 2pcs MG5516 Photoresistor at R1,R4. Note:The distance between the sensor and PCB is about 10mm.
 
Step 16: Put 2pcs Heat Shrinkable Tube on MG5516 Photoresistor.
Step 17: Install 2pcs Mini Vibrating Motor at M1,M2(Connect to XH2.54-2P Male Pin). Note that the wires cannot be kept too long(5mm is OK).
Step 18: Connect red and black wire to DC XH2.54-2P Male Pin. Note:Red wire connect to ‘ + ’ and Black wire connect to ‘ - ’. 
Step 19: Bend the three pins of PVC bracket.
Step 20: Paste PVC bracket onto PCB with a Double Sided Adhesive Tape.
 
Step 21: Paste 2pcs motor on PVC bracket.
Step 22: Connect Red wire to positive pole from battery socket and Black wire to another pin.Pay attention to distinguish between positive and negative.Note that the wires cannot be kept too long(3cm is OK).
Step 23: Paste CR2032 Battery Socket onto PVC bracket with a Double Sided Adhesive Tape.
Step 24: Install CR2032 battery (Not included) and enjoy the effect.
 
 
 

 

 
Quantity50+100+200+
Price$4.99$4.75$3.50
There are currently no product reviews.

ICStation doesn't accept any form of pay on delivery. Items used to be shipped after payment. Below are the payment methods we can accept at the moment:

1) Paypal Payment

PayPal is a secure and trusted payment processing service that allows you to shop online. PayPal can be used at icstation.com to purchase items by Credit Card (Visa, MasterCard, Discover, and American Express), Debit Card , or E-check (i.e. using your regular Bank Account). 



We are PayPal Verified 

 

2)  Bank Transfer / Wire Transfer / T/T

 

Bank Transfer / Wire Transfer / T/T payment methods are accepted for orders which the total price is up to US$300. The bank will charge about US$50 for the transfer fee if we do the payment in these ways. Feel free to contact us for bank payment details if you need pay via bank.

For other payment method, please contact us at orders@icstation-team.com for more details.

Customers who bought this product also purchased

SMD Component Welding Practice Board DIY Kit Analog Circuit Electronic Soldering Practice
$3.49
$4.99
31
DIY Kit SMD 15Bit RGB LED Flashing Analog Circuit Electronic Soldering SMD Component Welding Practice Board
$3.21
$4.59
30
25 Kinds of Tact Switch 125PCS Small Key Switch Button for DIY Module
$5.45
$7.79
30
Audio Spectrum 8x8 Colorful Flashing Light DIY Kit RGB Level Indicator Voice Spectrum Lights Lamp with Acrylic Shell
$9.09
$12.99
30
DIY Calculator Soldering Kit MCU Calculator Digital Tube Display with Acrylic Case
$16.09
$22.99
30
20mm 113KHz Ultrasonic Mist Maker Fogger Atomizer Ceramic Discs with Power Driver Board for Desktop Mini Humidifier
$5.45
$7.79
30
DC 3V-5V Arc Generator Igniter High Voltage Transformer Electronic Lighter for USB Cigarette Lighter
$5.08
$7.25
30
DIY Kit SMD RGB LED Flashing Lamp, USB 5V Breathing Light, Gradient Color Decorative Light SMD Soldering Practice Kits
$10.49
$14.99
30
DIY Colorful RGB LED Double Heart-shaped Flashing Light Lamp with Music DIY Electronic Kits for Love Gift
$9.09
$12.99
30
DIY Kit LED Dimming Table Lamp DC 3.7V-5V Electronic Soldering Practice Kit with Rechargeable 18650 Lithium Battery
$17.49
$24.99
30
DIY Kit Infrared Remote Control Lamp DC 5V-6V LED Light DIY Soldering Practice Kit
$7.35
$10.50
31
5V 8W Mini Portable USB Powered Electric Powered Soldering Iron Pen Tip Touch Switch with Stand
$5.94
$8.49
31

Your Recent History

Photosensitive Mobile Robot Simulation Firefly Electronic DIY Kit
$5.59
$7.99
31